Complete Error Log:
smartctl 6.6 2017-11-05 r4594 [x86_64-linux-5.0.1-pmagic64] (local build)
Copyright (C) 2002-17, Bruce Allen, Christian Franke,
www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Green
Device Model: WDC WD10EZRX-00L4HB0
Serial Number: WD-WCC4J5XDUZLJ
LU WWN Device Id: 5 0014ee 2b6379095
Firmware Version: 01.01A01
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Thu May 30 14:07:28 2019 EDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM feature is: Unavailable
Rd look-ahead is: Enabled
Write cache is: Enabled
DSN feature is: Unavailable
ATA Security is: Disabled, NOT FROZEN [SEC1]
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (13920) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 158) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x3035) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0
3 Spin_Up_Time POS--K 140 134 021 - 3983
4 Start_Stop_Count -O--CK 099 099 000 - 1652
5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0
7 Seek_Error_Rate -OSR-K 200 200 000 - 0
9 Power_On_Hours -O--CK 079 079 000 - 15557
10 Spin_Retry_Count -O--CK 100 100 000 - 0
11 Calibration_Retry_Count -O--CK 100 100 000 - 0
12 Power_Cycle_Count -O--CK 099 099 000 - 1636
192 Power-Off_Retract_Count -O--CK 200 200 000 - 191
193 Load_Cycle_Count -O--CK 131 131 000 - 208830
194 Temperature_Celsius -O---K 117 105 000 - 26
196 Reallocated_Event_Count -O--CK 200 200 000 - 0
197 Current_Pending_Sector -O--CK 200 200 000 - 0
198 Offline_Uncorrectable ----CK 200 200 000 - 0
199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 1
200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 5 Comprehensive SMART error log
0x03 GPL R/O 6 Ext. Comprehensive SMART error log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 NCQ Command Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa0-0xa7 GPL,SL VS 16 Device vendor specific log
0xa8-0xb7 GPL,SL VS 1 Device vendor specific log
0xbd GPL,SL VS 1 Device vendor specific log
0xc0 GPL,SL VS 1 Device vendor specific log
0xc1 GPL VS 93 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
Device Error Count: 32207 (device log contains only the most recent 24 errors)
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 32207 [14] occurred at disk power-on lifetime: 15557 hours (648 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 02 00 00 00 00 00 00 a0 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:00:02.834 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:02.833 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 00 00:00:02.833 SET FEATURES [Set transfer mode]
ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:00:02.833 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:02.832 IDENTIFY DEVICE
Error 32206 [13] occurred at disk power-on lifetime: 15557 hours (648 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 46 00 00 00 00 00 00 a0 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 03 00 46 00 00 00 00 00 00 a0 00 00:00:02.833 SET FEATURES [Set transfer mode]
ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:00:02.833 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:02.832 IDENTIFY DEVICE
c8 00 00 00 08 00 00 00 00 00 00 e0 00 00:00:02.818 READ DMA
ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:00:02.818 SET FEATURES [Enable SATA feature]
Error 32205 [12] occurred at disk power-on lifetime: 15557 hours (648 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 02 00 00 00 00 00 00 a0 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:00:02.833 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:02.832 IDENTIFY DEVICE
c8 00 00 00 08 00 00 00 00 00 00 e0 00 00:00:02.818 READ DMA
ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:00:02.818 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:02.817 IDENTIFY DEVICE
Error 32204 [11] occurred at disk power-on lifetime: 15557 hours (648 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 08 00 00 00 00 00 00 e0 00 Error: ABRT 8 sectors at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
c8 00 00 00 08 00 00 00 00 00 00 e0 00 00:00:02.818 READ DMA
ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:00:02.818 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:02.817 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 00 00:00:02.817 SET FEATURES [Set transfer mode]
ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:00:02.817 SET FEATURES [Enable SATA feature]
Error 32203 [10] occurred at disk power-on lifetime: 15557 hours (648 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 02 00 00 00 00 00 00 a0 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:00:02.818 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:02.817 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 00 00:00:02.817 SET FEATURES [Set transfer mode]
ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:00:02.817 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:02.816 IDENTIFY DEVICE
Error 32202 [9] occurred at disk power-on lifetime: 15557 hours (648 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 46 00 00 00 00 00 00 a0 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 03 00 46 00 00 00 00 00 00 a0 00 00:00:02.817 SET FEATURES [Set transfer mode]
ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:00:02.817 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:02.816 IDENTIFY DEVICE
c8 00 00 00 08 00 00 00 00 00 00 e0 00 00:00:02.802 READ DMA
ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:00:02.802 SET FEATURES [Enable SATA feature]
Error 32201 [8] occurred at disk power-on lifetime: 15557 hours (648 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 02 00 00 00 00 00 00 a0 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:00:02.817 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:02.816 IDENTIFY DEVICE
c8 00 00 00 08 00 00 00 00 00 00 e0 00 00:00:02.802 READ DMA
ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:00:02.802 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:02.801 IDENTIFY DEVICE
Error 32200 [7] occurred at disk power-on lifetime: 15557 hours (648 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 08 00 00 00 00 00 00 e0 00 Error: ABRT 8 sectors at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
c8 00 00 00 08 00 00 00 00 00 00 e0 00 00:00:02.802 READ DMA
ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:00:02.802 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:02.801 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 00 00:00:02.801 SET FEATURES [Set transfer mode]
ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:00:02.801 SET FEATURES [Enable SATA feature]
Error 32199 [6] occurred at disk power-on lifetime: 15557 hours (648 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 02 00 00 00 00 00 00 a0 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:00:02.802 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:02.801 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 00 00:00:02.801 SET FEATURES [Set transfer mode]
ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:00:02.801 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:02.800 IDENTIFY DEVICE
Error 32198 [5] occurred at disk power-on lifetime: 15557 hours (648 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 46 00 00 00 00 00 00 a0 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 03 00 46 00 00 00 00 00 00 a0 00 00:00:02.801 SET FEATURES [Set transfer mode]
ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:00:02.801 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:02.800 IDENTIFY DEVICE
c8 00 00 00 08 00 00 00 00 00 00 e0 00 00:00:02.786 READ DMA
ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:00:02.786 SET FEATURES [Enable SATA feature]
Error 32197 [4] occurred at disk power-on lifetime: 15557 hours (648 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 02 00 00 00 00 00 00 a0 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:00:02.801 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:02.800 IDENTIFY DEVICE
c8 00 00 00 08 00 00 00 00 00 00 e0 00 00:00:02.786 READ DMA
ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:00:02.786 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:02.785 IDENTIFY DEVICE
Error 32196 [3] occurred at disk power-on lifetime: 15557 hours (648 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 08 00 00 00 00 00 00 e0 00 Error: ABRT 8 sectors at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
c8 00 00 00 08 00 00 00 00 00 00 e0 00 00:00:02.786 READ DMA
ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:00:02.786 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:02.785 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 00 00:00:02.785 SET FEATURES [Set transfer mode]
ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:00:02.785 SET FEATURES [Enable SATA feature]
Error 32195 [2] occurred at disk power-on lifetime: 15557 hours (648 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 02 00 00 00 00 00 00 a0 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:00:02.786 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:02.785 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 00 00:00:02.785 SET FEATURES [Set transfer mode]
ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:00:02.785 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:02.784 IDENTIFY DEVICE
Error 32194 [1] occurred at disk power-on lifetime: 15557 hours (648 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 46 00 00 00 00 00 00 a0 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 03 00 46 00 00 00 00 00 00 a0 00 00:00:02.785 SET FEATURES [Set transfer mode]
ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:00:02.785 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:02.784 IDENTIFY DEVICE
c8 00 00 00 08 00 00 00 00 00 00 e0 00 00:00:02.770 READ DMA
ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:00:02.770 SET FEATURES [Enable SATA feature]
Error 32193 [0] occurred at disk power-on lifetime: 15557 hours (648 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 02 00 00 00 00 00 00 a0 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:00:02.785 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:02.784 IDENTIFY DEVICE
c8 00 00 00 08 00 00 00 00 00 00 e0 00 00:00:02.770 READ DMA
ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:00:02.770 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:02.769 IDENTIFY DEVICE
Error 32192 [23] occurred at disk power-on lifetime: 15557 hours (648 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 08 00 00 00 00 00 00 e0 00 Error: ABRT 8 sectors at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
c8 00 00 00 08 00 00 00 00 00 00 e0 00 00:00:02.770 READ DMA
ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:00:02.770 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:02.769 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 00 00:00:02.769 SET FEATURES [Set transfer mode]
ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:00:02.769 SET FEATURES [Enable SATA feature]
Error 32191 [22] occurred at disk power-on lifetime: 15557 hours (648 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 02 00 00 00 00 00 00 a0 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:00:02.770 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:02.769 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 00 00:00:02.769 SET FEATURES [Set transfer mode]
ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:00:02.769 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:02.768 IDENTIFY DEVICE
Error 32190 [21] occurred at disk power-on lifetime: 15557 hours (648 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 46 00 00 00 00 00 00 a0 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 03 00 46 00 00 00 00 00 00 a0 00 00:00:02.769 SET FEATURES [Set transfer mode]
ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:00:02.769 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:02.768 IDENTIFY DEVICE
c8 00 00 00 08 00 00 00 00 00 00 e0 00 00:00:02.754 READ DMA
ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:00:02.754 SET FEATURES [Enable SATA feature]
Error 32189 [20] occurred at disk power-on lifetime: 15557 hours (648 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 02 00 00 00 00 00 00 a0 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:00:02.769 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:02.768 IDENTIFY DEVICE
c8 00 00 00 08 00 00 00 00 00 00 e0 00 00:00:02.754 READ DMA
ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:00:02.754 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:02.753 IDENTIFY DEVICE
Error 32188 [19] occurred at disk power-on lifetime: 15557 hours (648 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 08 00 00 00 00 00 00 e0 00 Error: ABRT 8 sectors at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
c8 00 00 00 08 00 00 00 00 00 00 e0 00 00:00:02.754 READ DMA
ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:00:02.754 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:02.753 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 00 00:00:02.753 SET FEATURES [Set transfer mode]
ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:00:02.753 SET FEATURES [Enable SATA feature]
Error 32187 [18] occurred at disk power-on lifetime: 15557 hours (648 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 02 00 00 00 00 00 00 a0 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:00:02.754 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:02.753 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 00 00:00:02.753 SET FEATURES [Set transfer mode]
ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:00:02.753 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:02.752 IDENTIFY DEVICE
Error 32186 [17] occurred at disk power-on lifetime: 15557 hours (648 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 46 00 00 00 00 00 00 a0 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 03 00 46 00 00 00 00 00 00 a0 00 00:00:02.753 SET FEATURES [Set transfer mode]
ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:00:02.753 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:02.752 IDENTIFY DEVICE
c8 00 00 00 08 00 00 00 00 00 00 e0 00 00:00:02.726 READ DMA
ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:00:02.726 SET FEATURES [Enable SATA feature]
Error 32185 [16] occurred at disk power-on lifetime: 15557 hours (648 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 02 00 00 00 00 00 00 a0 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:00:02.753 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:02.752 IDENTIFY DEVICE
c8 00 00 00 08 00 00 00 00 00 00 e0 00 00:00:02.726 READ DMA
ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:00:02.726 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:02.725 IDENTIFY DEVICE
Error 32184 [15] occurred at disk power-on lifetime: 15557 hours (648 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 08 00 00 00 00 00 00 e0 00 Error: ABRT 8 sectors at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
c8 00 00 00 08 00 00 00 00 00 00 e0 00 00:00:02.726 READ DMA
ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:00:02.726 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:02.725 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 00 00:00:02.725 SET FEATURES [Set transfer mode]
ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:00:02.725 SET FEATURES [Enable SATA feature]
SMART Error Log Version: 1
Warning: ATA error count 3398 inconsistent with error log pointer 5
ATA Error Count: 3398 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 3398 occurred at disk power-on lifetime: 15557 hours (648 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 02 00 00 00 a0 Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 10 02 00 00 00 a0 00 00:00:02.834 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 00 00:00:02.833 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 00:00:02.833 SET FEATURES [Set transfer mode]
ef 10 02 00 00 00 a0 00 00:00:02.833 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 00 00:00:02.832 IDENTIFY DEVICE
Error 3397 occurred at disk power-on lifetime: 15557 hours (648 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 46 00 00 00 a0 Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 03 46 00 00 00 a0 00 00:00:02.833 SET FEATURES [Set transfer mode]
ef 10 02 00 00 00 a0 00 00:00:02.833 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 00 00:00:02.832 IDENTIFY DEVICE
c8 00 08 00 00 00 e0 00 00:00:02.818 READ DMA
ef 10 02 00 00 00 a0 00 00:00:02.818 SET FEATURES [Enable SATA feature]
Error 3396 occurred at disk power-on lifetime: 15557 hours (648 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 02 00 00 00 a0 Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 10 02 00 00 00 a0 00 00:00:02.833 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 00 00:00:02.832 IDENTIFY DEVICE
c8 00 08 00 00 00 e0 00 00:00:02.818 READ DMA
ef 10 02 00 00 00 a0 00 00:00:02.818 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 00 00:00:02.817 IDENTIFY DEVICE
Error 3395 occurred at disk power-on lifetime: 15557 hours (648 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 08 00 00 00 e0 Error: ABRT 8 sectors at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 00 00 00 e0 00 00:00:02.818 READ DMA
ef 10 02 00 00 00 a0 00 00:00:02.818 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 00 00:00:02.817 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 00:00:02.817 SET FEATURES [Set transfer mode]
ef 10 02 00 00 00 a0 00 00:00:02.817 SET FEATURES [Enable SATA feature]
Error 3394 occurred at disk power-on lifetime: 15557 hours (648 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 02 00 00 00 a0 Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 10 02 00 00 00 a0 00 00:00:02.818 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 00 00:00:02.817 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 00:00:02.817 SET FEATURES [Set transfer mode]
ef 10 02 00 00 00 a0 00 00:00:02.817 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 00 00:00:02.816 IDENTIFY DEVICE
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 15557 -
# 2 Short offline Completed without error 00% 15554 -
# 3 Extended offline Aborted by host 90% 15554 -
# 4 Short offline Completed without error 00% 15554 -
# 5 Short offline Completed without error 00% 15554 -
# 6 Short offline Completed without error 00% 15553 -
# 7 Short offline Completed without error 00% 10690 -
# 8 Conveyance offline Completed without error 00% 8589 -
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 15557 -
# 2 Short offline Completed without error 00% 15554 -
# 3 Extended offline Aborted by host 90% 15554 -
# 4 Short offline Completed without error 00% 15554 -
# 5 Short offline Completed without error 00% 15554 -
# 6 Short offline Completed without error 00% 15553 -
# 7 Short offline Completed without error 00% 10690 -
# 8 Conveyance offline Completed without error 00% 8589 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 258 (0x0102)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 26 Celsius
Power Cycle Min/Max Temperature: 26/26 Celsius
Lifetime Min/Max Temperature: 14/38 Celsius
Under/Over Temperature Limit Count: 0/0
Vendor specific:
01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 0/60 Celsius
Min/Max Temperature Limit: -41/85 Celsius
Temperature History Size (Index): 478 (90)
Index Estimated Time Temperature Celsius
91 2019-05-30 06:10 23 ****
92 2019-05-30 06:11 23 ****
93 2019-05-30 06:12 23 ****
94 2019-05-30 06:13 ? -
95 2019-05-30 06:14 24 *****
96 2019-05-30 06:15 ? -
97 2019-05-30 06:16 27 ********
98 2019-05-30 06:17 ? -
99 2019-05-30 06:18 27 ********
100 2019-05-30 06:19 ? -
101 2019-05-30 06:20 28 *********
102 2019-05-30 06:21 ? -
103 2019-05-30 06:22 28 *********
104 2019-05-30 06:23 28 *********
105 2019-05-30 06:24 28 *********
106 2019-05-30 06:25 29 **********
107 2019-05-30 06:26 30 ***********
... ..( 2 skipped). .. ***********
110 2019-05-30 06:29 30 ***********
111 2019-05-30 06:30 31 ************
112 2019-05-30 06:31 31 ************
113 2019-05-30 06:32 ? -
114 2019-05-30 06:33 31 ************
... ..( 2 skipped). .. ************
117 2019-05-30 06:36 31 ************
118 2019-05-30 06:37 32 *************
119 2019-05-30 06:38 31 ************
... ..( 2 skipped). .. ************
122 2019-05-30 06:41 31 ************
123 2019-05-30 06:42 32 *************
... ..( 2 skipped). .. *************
126 2019-05-30 06:45 32 *************
127 2019-05-30 06:46 33 **************
... ..( 2 skipped). .. **************
130 2019-05-30 06:49 33 **************
131 2019-05-30 06:50 34 ***************
... ..( 3 skipped). .. ***************
135 2019-05-30 06:54 34 ***************
136 2019-05-30 06:55 35 ****************
... ..( 54 skipped). .. ****************
191 2019-05-30 07:50 35 ****************
192 2019-05-30 07:51 34 ***************
... ..( 4 skipped). .. ***************
197 2019-05-30 07:56 34 ***************
198 2019-05-30 07:57 33 **************
... ..( 18 skipped). .. **************
217 2019-05-30 08:16 33 **************
218 2019-05-30 08:17 32 *************
... ..( 6 skipped). .. *************
225 2019-05-30 08:24 32 *************
226 2019-05-30 08:25 31 ************
... ..( 27 skipped). .. ************
254 2019-05-30 08:53 31 ************
255 2019-05-30 08:54 32 *************
... ..( 3 skipped). .. *************
259 2019-05-30 08:58 32 *************
260 2019-05-30 08:59 33 **************
... ..( 4 skipped). .. **************
265 2019-05-30 09:04 33 **************
266 2019-05-30 09:05 34 ***************
267 2019-05-30 09:06 34 ***************
268 2019-05-30 09:07 35 ****************
269 2019-05-30 09:08 35 ****************
270 2019-05-30 09:09 ? -
271 2019-05-30 09:10 22 ***
272 2019-05-30 09:11 ? -
273 2019-05-30 09:12 24 *****
274 2019-05-30 09:13 25 ******
275 2019-05-30 09:14 26 *******
... ..( 8 skipped). .. *******
284 2019-05-30 09:23 26 *******
285 2019-05-30 09:24 27 ********
... ..( 3 skipped). .. ********
289 2019-05-30 09:28 27 ********
290 2019-05-30 09:29 28 *********
... ..( 7 skipped). .. *********
298 2019-05-30 09:37 28 *********
299 2019-05-30 09:38 ? -
300 2019-05-30 09:39 28 *********
301 2019-05-30 09:40 28 *********
302 2019-05-30 09:41 27 ********
... ..( 2 skipped). .. ********
305 2019-05-30 09:44 27 ********
306 2019-05-30 09:45 ? -
307 2019-05-30 09:46 24 *****
308 2019-05-30 09:47 ? -
309 2019-05-30 09:48 25 ******
310 2019-05-30 09:49 ? -
311 2019-05-30 09:50 26 *******
312 2019-05-30 09:51 26 *******
313 2019-05-30 09:52 30 ***********
... ..( 52 skipped). .. ***********
366 2019-05-30 10:45 30 ***********
367 2019-05-30 10:46 31 ************
... ..( 51 skipped). .. ************
419 2019-05-30 11:38 31 ************
420 2019-05-30 11:39 ? -
421 2019-05-30 11:40 18 -
422 2019-05-30 11:41 19 -
423 2019-05-30 11:42 ? -
424 2019-05-30 11:43 27 ********
425 2019-05-30 11:44 27 ********
426 2019-05-30 11:45 ? -
427 2019-05-30 11:46 28 *********
428 2019-05-30 11:47 ? -
429 2019-05-30 11:48 25 ******
430 2019-05-30 11:49 ? -
431 2019-05-30 11:50 27 ********
432 2019-05-30 11:51 27 ********
433 2019-05-30 11:52 ? -
434 2019-05-30 11:53 26 *******
... ..( 4 skipped). .. *******
439 2019-05-30 11:58 26 *******
440 2019-05-30 11:59 ? -
441 2019-05-30 12:00 29 **********
... ..( 4 skipped). .. **********
446 2019-05-30 12:05 29 **********
447 2019-05-30 12:06 ? -
448 2019-05-30 12:07 30 ***********
449 2019-05-30 12:08 ? -
450 2019-05-30 12:09 28 *********
451 2019-05-30 12:10 28 *********
452 2019-05-30 12:11 28 *********
453 2019-05-30 12:12 ? -
454 2019-05-30 12:13 21 **
455 2019-05-30 12:14 21 **
456 2019-05-30 12:15 21 **
457 2019-05-30 12:16 22 ***
458 2019-05-30 12:17 ? -
459 2019-05-30 12:18 24 *****
460 2019-05-30 12:19 24 *****
461 2019-05-30 12:20 25 ******
462 2019-05-30 12:21 ? -
463 2019-05-30 12:22 28 *********
464 2019-05-30 12:23 28 *********
465 2019-05-30 12:24 ? -
466 2019-05-30 12:25 24 *****
467 2019-05-30 12:26 24 *****
468 2019-05-30 12:27 25 ******
... ..( 2 skipped). .. ******
471 2019-05-30 12:30 25 ******
472 2019-05-30 12:31 26 *******
473 2019-05-30 12:32 26 *******
474 2019-05-30 12:33 26 *******
475 2019-05-30 12:34 27 ********
476 2019-05-30 12:35 27 ********
477 2019-05-30 12:36 27 ********
0 2019-05-30 12:37 ? -
1 2019-05-30 12:38 21 **
... ..( 2 skipped). .. **
4 2019-05-30 12:41 21 **
5 2019-05-30 12:42 22 ***
6 2019-05-30 12:43 ? -
7 2019-05-30 12:44 20 *
8 2019-05-30 12:45 20 *
9 2019-05-30 12:46 21 **
10 2019-05-30 12:47 21 **
11 2019-05-30 12:48 22 ***
12 2019-05-30 12:49 22 ***
13 2019-05-30 12:50 23 ****
... ..( 3 skipped). .. ****
17 2019-05-30 12:54 23 ****
18 2019-05-30 12:55 24 *****
19 2019-05-30 12:56 24 *****
20 2019-05-30 12:57 24 *****
21 2019-05-30 12:58 25 ******
22 2019-05-30 12:59 25 ******
23 2019-05-30 13:00 25 ******
24 2019-05-30 13:01 26 *******
... ..( 7 skipped). .. *******
32 2019-05-30 13:09 26 *******
33 2019-05-30 13:10 27 ********
34 2019-05-30 13:11 27 ********
35 2019-05-30 13:12 27 ********
36 2019-05-30 13:13 28 *********
... ..( 24 skipped). .. *********
61 2019-05-30 13:38 28 *********
62 2019-05-30 13:39 ? -
63 2019-05-30 13:40 21 **
64 2019-05-30 13:41 ? -
65 2019-05-30 13:42 23 ****
66 2019-05-30 13:43 ? -
67 2019-05-30 13:44 23 ****
68 2019-05-30 13:45 23 ****
69 2019-05-30 13:46 23 ****
70 2019-05-30 13:47 24 *****
71 2019-05-30 13:48 ? -
72 2019-05-30 13:49 27 ********
73 2019-05-30 13:50 ? -
74 2019-05-30 13:51 23 ****
75 2019-05-30 13:52 23 ****
76 2019-05-30 13:53 23 ****
77 2019-05-30 13:54 ? -
78 2019-05-30 13:55 24 *****
79 2019-05-30 13:56 24 *****
80 2019-05-30 13:57 24 *****
81 2019-05-30 13:58 25 ******
82 2019-05-30 13:59 25 ******
83 2019-05-30 14:00 25 ******
84 2019-05-30 14:01 26 *******
85 2019-05-30 14:02 26 *******
86 2019-05-30 14:03 26 *******
87 2019-05-30 14:04 ? -
88 2019-05-30 14:05 21 **
89 2019-05-30 14:06 22 ***
90 2019-05-30 14:07 22 ***
SCT Error Recovery Control command not supported
Device Statistics (GP/SMART Log 0x04) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0008 2 0 Device-to-host non-data FIS retries
0x0009 2 1 Transition from drive PhyRdy to drive PhyNRdy
0x000a 2 1 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
0x8000 4 87 Vendor specific