BSoD immediately after run TestDisk

How to use TestDisk to recover lost partition
Post Reply
Message
Author
KIPPIE408
Posts: 1
Joined: 07 Jul 2017, 18:30

BSoD immediately after run TestDisk

#1 Post by KIPPIE408 » 07 Jul 2017, 18:46

Symptom: BSoD is shown immediately after run TestDisk, as shown in the title.

Conditions:
Windows 10 version 1703, build 15063.447, 64-bit.
* Checked from winver. Upgraded from Windows 8.1.
TestDisk 7.0 or 7.1-WIP (occurs on both versions).
3.5-inch SATA hard disk to make restored ("Disk A") connected to a SATA port on motherboard directly.
* If Disk A is connected via SATA-to-USB 2.0 connector, no BSoD is shown. But for nine out of ten, deeper search fails because a short disconnection/reconnection comes out.


Log & Messages: BSoD says SYSTEM THREAD EXCEPTION NOT HANDLED, and that failure was from ntfs.sys.

Code: Select all


Sat Jul  8 02:21:22 2017
Command line: TestDisk

TestDisk 7.0, Data Recovery Utility, April 2015
Christophe GRENIER <grenier@cgsecurity.org>
http://www.cgsecurity.org
OS: Windows 8 (9200)
Compiler: GCC 4.8, Cygwin 1007.34
Compilation date: 2015-04-18T13:01:55
ext2fs lib: 1.42.8, ntfs lib: 10:0:0, reiserfs lib: 0.3.1-rc8, ewf lib: 20120504, curses lib: ncurses 5.9
disk_get_size_win32 IOCTL_DISK_GET_LENGTH_INFO(/dev/sda)=2000398934016
disk_get_size_win32 IOCTL_DISK_GET_LENGTH_INFO(/dev/sdb)=500107862016
disk_get_size_win32 IOCTL_DISK_GET_LENGTH_INFO(/dev/sdc)=2000398934016
disk_get_size_win32 IOCTL_DISK_GET_LENGTH_INFO(/dev/sdd)=500107862016
disk_get_size_win32 IOCTL_DISK_GET_LENGTH_INFO(\\.\PhysicalDrive0)=2000398934016
disk_get_size_win32 IOCTL_DISK_GET_LENGTH_INFO(\\.\PhysicalDrive1)=500107862016
disk_get_size_win32 IOCTL_DISK_GET_LENGTH_INFO(\\.\PhysicalDrive2)=2000398934016
disk_get_size_win32 IOCTL_DISK_GET_LENGTH_INFO(\\.\PhysicalDrive3)=500107862016
disk_get_size_win32 IOCTL_DISK_GET_LENGTH_INFO(\\.\C:)=499602450944
disk_get_size_win32 IOCTL_DISK_GET_LENGTH_INFO(\\.\D:)=2000395805184
disk_get_size_win32 IOCTL_DISK_GET_LENGTH_INFO(\\.\E:)=1476108746752
disk_get_size_win32 IOCTL_DISK_GET_LENGTH_INFO(\\.\F:)=524286951424
filewin32_getfilesize(\\.\H:) GetFileSize err 잘못된 기능입니다.

filewin32_setfilepointer(\\.\H:) SetFilePointer err 잘못된 기능입니다.

Warning: can't get size for \\.\H:
disk_get_size_win32 IOCTL_DISK_GET_LENGTH_INFO(\\.\M:)=500107804672
Hard disk list
Disk /dev/sda - 2000 GB / 1863 GiB - CHS 258401 240 63, sector size=512
Disk /dev/sdb - 500 GB / 465 GiB - CHS 60801 255 63, sector size=512
Disk /dev/sdc - 2000 GB / 1863 GiB - CHS 243201 255 63, sector size=512
Disk /dev/sdd - 500 GB / 465 GiB - CHS 60801 255 63, sector size=512
Drive C: - 499 GB / 465 GiB - CHS 60739 255 63, sector size=512
Drive D: - 2000 GB / 1863 GiB - CHS 258400 240 63, sector size=512
Drive E: - 1476 GB / 1374 GiB - CHS 179459 255 63, sector size=512
Drive F: - 524 GB / 488 GiB - CHS 63740 255 63, sector size=512
Drive M: - 500 GB / 465 GiB - CHS 60801 255 63, sector size=512

SIGHUP detected! TestDisk has been killed.

Sponsored links

User avatar
cgrenier
Site Admin
Posts: 3770
Joined: 18 Feb 2012, 15:08
Location: Le Perreux Sur Marne, France
Contact:

Re: BSoD immediately after run TestDisk

#2 Post by cgrenier » 08 Jul 2017, 09:19

You can try to boot from a Linux LiveUSB, see https://www.cgsecurity.org/testdisk.pdf and run TestDisk to check if you have the same problem.
If it's an hardware problem, contacting a data recovery company may be the only solution to recover your data...

Post Reply

Who is online

Users browsing this forum: No registered users and 0 guests